- Can you use Ethernet cable for rs485?
- Can I use CAT5e jack with cat6 cable?
- What type of cable is used for rs485?
- How many wires is rs485?
- Where is rs485 used?
- What voltage is rs485?
- What is the difference between rs485 and Ethernet?
- Is there a difference between cat5e and cat6 keystone jacks?
- What is a rs485 cable?
- Is rs485 a protocol?
- What is the maximum distance for rs485?
- Does rs485 need termination?
- Should I use Cat 5e or Cat 6?
- Is rj45 the same as cat6?
Can you use Ethernet cable for rs485?
cat5e can be used up to 100m ethernet link.
it has 4 twisted pairs so technically you should be able to use it for RS485 or RS422.
if using 485, you need two twisted pairs so remaining 4 wires can be used for power.
485 cable should be shielded but twisted pairs of cat5e may work for some environments and baud rates..
Can I use CAT5e jack with cat6 cable?
Active Member. The Cat5e plugs should work fine with Cat6 cable, with sligh differences in specifications. That said, there may be slight differences in wire size, so make sure those plugs are a match for the wire size in the Cat6 cable.
What type of cable is used for rs485?
Category 5 cable is available as shielded twisted pair (STP) as well as unshielded twisted pair (UTP) and generally exceeds the recommendations for RS-422 making it an excellent choice for RS-422 and RS-485 systems.
How many wires is rs485?
Full duplex operation RS-485, like RS-422, can be made full-duplex by using four wires. Since RS-485 is a multi-point specification, however, this is not necessary or desirable in many cases. RS-485 and RS-422 can interoperate with certain restrictions.
Where is rs485 used?
The RS485 standard is used when high speed serial data communications of 10 Mbps is needed. RS485 was developed to provide high speed data. The standard is defined by industry telecommunications bodies and may be referred to most commonly as RS485, but references to EIA485 or TIA-485 may also be seen.
What voltage is rs485?
RS485/RS422 Transceivers Operate from 3V to 5.5V Supplies and Withstand ±60V Faults.
What is the difference between rs485 and Ethernet?
Ethernet (IEEE 802.3) is the most broadly used network protocol these days. It is also a serial communication standard. … The major drawback of RS-485 is its limited communication speed which is maxed out at 10 Mbaud. RS-485 is designed for a master/slave topology.
Is there a difference between cat5e and cat6 keystone jacks?
Both are twisted pair cables consisting of copper wires. The Cat5e Keystone Jack supports speed limit upto 1000MBPS and the Cat6 cables has a speed limit upto 10GBPS over 120-150 feet. … Even though Cat6 can be identified without the print as it thicker than Cat5e as it consists of a thicker copper wire.
What is a rs485 cable?
EIA-485 (formerly RS-485 or RS485) is a specification for the physical layer of a network that uses the difference in voltages between two wires (Three wire) to conveys data. The resistance of the twisted pair cable will drop the voltage difference as it travels down the wire. …
Is rs485 a protocol?
RS485 is a protocol similar to RS232 that is used to implement serial data communication. The two protocols use different electric signals to enable data transmission. One of the reasons that RS485 interfacing is employed in industrial settings is its ability to serve several devices attached to the same bus.
What is the maximum distance for rs485?
4,000 feetThe standard specifies electrical characteristics of a driver and receiver, and does not specify any data protocol or connectors. RS485 is popular for inexpensive local networks, multidrop communication links and long haul data transfer over distances of up to 4,000 feet.
Does rs485 need termination?
Both ends must be terminated since the direction of propagation is bidirectional. In case of an RS485 twisted pair cable this termination is typically between 120 and 130 Ω. Here is a simple schematic of how the end of the lines should be terminated: “RT” is the 120 Ω termination resistor.
Should I use Cat 5e or Cat 6?
Cat 6 is cable that’s more reliable at higher speeds than Cat 5 or Cat 5e. … Cat 5e cable is enhanced to reduce interference so that it can reliably deliver gigabit speeds. However, Gigabit Ethernet still pushes the cable to its limits.
Is rj45 the same as cat6?
Cat5e RJ45 cable has lower level of transmission performance, while Cat6 RJ45 cable is optimized with a 250MHz bandwidth, higher data rate and stronger resistance to crosstalk and noise.